Great leightweight receiver. I build a micro quad with this DSMX Pro receiver, a F4 brushed controller and reuesed parts of a defective Hubsan H107D. First I soldered the DSMX Pro receiver to UART1, because it can handle 5V. The receiecer will funtion on this port but you can not get it to bind mode. Instead of RX1 I used RX3 then. In Betaflight CLI enter: set spektrum_sat_bind=9 set spektrum_sat_bind_autoreset=0 (This is important, otherwise the save cmmand will immediately reset the bind mode) save Power cycle If motors are installed already use USB power only until all settings are done correctly! I coud bind my Devo8 with DeviationTX Software in 8CH DSMX mode. If you do not see anyting in the betaflight receiver page after binding, restore to contoller defaults and set the RX serial port and receiver and brushed settings again. Defaults will also reset spektrum_sat_bind to 0, otherwise do this step manualy to avoid binding mode ater each power cycle. The receiver works great, I did not make range test because I want to use it indoors only. Meaning of the spectrum bind modes: 3 for DSM2 1024bit/22ms 5 for DSM2 2048bit/11ms default AlienWii32 7 for DSMX 1024bit/22ms used by Devo 7e 8 for DSMX 2048bit/22ms Used by new DXe 9 for DSMX 2048bit/11ms

Great leightweight receiver. I build a micro quad with this DSMX Pro receiver, a F4 brushed controller and reuesed parts of a defective Hubsan H107D. First I soldered the DSMX Pro receiver to UART1, because it can handle 5V. The receiecer will funtion on this port but you can not get it to bind mode. Instead of RX1 I used RX3 then. In Betaflight CLI enter: set spektrum_sat_bind=9 set spektrum_sat_bind_autoreset=0 (This is important, otherwise the save cmmand will immediately reset the bind mode) save Power cycle If motors are installed already use USB power only until all settings are done correctly! I coud bind my Devo8 with DeviationTX Software in 8CH DSMX mode. If you do not see anyting in the betaflight receiver page after binding, restore to contoller defaults and set the RX serial port and receiver and brushed settings again. Defaults will also reset spektrum_sat_bind to 0, otherwise do this step manualy to avoid binding mode ater each power cycle. The receiver works great, I did not make range test because I want to use it indoors only. Meaning of the spectrum bind modes: 3 for DSM2 1024bit/22ms 5 for DSM2 2048bit/11ms default AlienWii32 7 for DSMX 1024bit/22ms used by Devo 7e 8 for DSMX 2048bit/22ms Used by new DXe 9 for DSMX 2048bit/11ms

Great leightweight receiver. I build a micro quad with this DSMX Pro receiver, a F4 brushed controller and reuesed parts of a defective Hubsan H107D. First I soldered the DSMX Pro receiver to UART1, because it can handle 5V. The receiecer will funtion on this port but you can not get it to bind mode. Instead of RX1 I used RX3 then. In Betaflight CLI enter: set spektrum_sat_bind=9 set spektrum_sat_bind_autoreset=0 (This is important, otherwise the save cmmand will immediately reset the bind mode) save Power cycle If motors are installed already use USB power only until all settings are done correctly! I coud bind my Devo8 with DeviationTX Software in 8CH DSMX mode. If you do not see anyting in the betaflight receiver page after binding, restore to contoller defaults and set the RX serial port and receiver and brushed settings again. Defaults will also reset spektrum_sat_bind to 0, otherwise do this step manualy to avoid binding mode ater each power cycle. The receiver works great, I did not make range test because I want to use it indoors only. Meaning of the spectrum bind modes: 3 for DSM2 1024bit/22ms 5 for DSM2 2048bit/11ms default AlienWii32 7 for DSMX 1024bit/22ms used by Devo 7e 8 for DSMX 2048bit/22ms Used by new DXe 9 for DSMX 2048bit/11ms

very good DSMX receiver with only 0.8g fit in all micro drones less 120mm You can use it for dustx58 to replace the FrSky with dsmx

very good DSMX receiver with only 0.8g fit in all micro drones less 120mm You can use it for dustx58 to replace the FrSky with dsmx

very good DSMX receiver with only 0.8g fit in all micro drones less 120mm You can use it for dustx58 to replace the FrSky with dsmx